LED Downlights

1 product
The VOLTAFIT LED downlights are assembled with a high-lumen chip on board (CoB) from CITIZEN LED (Japan) with a beam angle of 120°. The efficacy of the luminaire is 111lm/watt... Read more

The VOLTAFIT LED downlights are assembled with a high-lumen chip on board (CoB) from CITIZEN LED (Japan) with a beam angle of 120°. The efficacy of the luminaire is 111lm/watt giving the best possible lighting experience which is cost-effective and environmentally friendly. The downlight comes in two powerful versions of 15w and 35w including the LED driver with 96% efficiency.

The downlight is connected safely directly to the mains voltage 220-240Vac (there is also a 110-120Vac version for the American market)

There is no need for any maintenance and once installed it will save you up to 80% in electricity costs. The impressive life span of 50,000 hours will eliminate the need to replace your bulbs for the next 15-17 years (average daily usage of 8 hours). 

ROUND DIAMOND CUT REFLECTOR

The engineering team of Voltacon was inspired by the shape of diamonds when they developed the new LED downlighters. The reflector has a similar shape and contours to a round diamond. This shape boasts exceptional light reflection. The light engine is manufactured in Japan by the renowned company CITIZEL LED. The high-power chips of board (CoB) achieved the highest levels of the lumen in the world (145lumen/watt). The colour rendering index has improved from 70 to over 85 while retaining the luminous flux and luminous efficacy.


The LED driver is not visible, we integrated the printed circuit board in the aluminium housing of the LED downlighter. The main advantages are better heating dissipation and easier installation. There is only a 3-core cable (live, neutral and earth) that is connected directly to the mains voltage (100-240VAC.

CoB stands for Chip on Board this is an arrangement for high-power lighting where LED dies are directly mounted on a copper or aluminium board.

How to choose and FAQ

Products

Skip to results list

Filters

1 item

Active filters:

Fire rated: Yes Remove
Fire rated
1

Filter 1 filter applied

Active filters:

Fire rated: Yes Remove
Fire rated
1
  • LED Fire Rated Downlight 8W, 600lm, IP65, Dimmable, Tri-Colour Selectable, White Bezel, Twin Pack, Altair

    281130
    Copy

    LED Fire Rated Downlight 8W, 600lm, IP65, Dimmable, Tri-Colour Selectable, White Bezel, Twin Pack, Altair

    8W600 lmIP65
    $43.00 inc VAT $35.83ex VATIn stock

How to choose LED Downlights

Colour. Warm white (2700K or 3000K) suits living rooms and bedrooms. Natural white (4000K) suits kitchens, bathrooms and work areas. Our downlights come in 2700K, 3000K and 4000K, and several of our fire rated models switch between colours, so you can match one colour across the room.

Fire rated or not. Where the ceiling is a fire barrier, for example between flats or below a room upstairs, each hole you cut weakens it. A fire rated downlight is made to restore that fire resistance. Our fire rated models state 30, 60 or 90 minutes in the spec table. See our fire rated downlights.

Bathrooms. Above the bath or shower (zone 1) you need at least IPX4, or IPX5 where water jets are used. Our IP65 fire rated downlights meet that.

Hole size and dimming. Check the cut-out before you order: our fire rated models need about 65 to 75mm, our larger downlights up to 170mm. Most models are dimmable or have a dimmable option; use an LED dimmer switch.

Common questions

Do I need fire rated downlights?

If the ceiling forms a fire barrier, for example between flats or below a habitable room, fire rated downlights are made to restore the fire resistance the holes take away. This falls under Building Regulations Part B, so if you are not sure, ask a qualified electrician or your building control body.

Should I choose 3000K or 4000K for my kitchen?

3000K gives a warmer, homely light and 4000K a brighter, crisper light over worktops. If you cannot decide, a colour switchable downlight lets you choose after fitting.

Can I put downlights in a bathroom?

Yes, if the IP rating suits the zone. Under BS 7671, zone 1 above the bath or shower needs at least IPX4 (IPX5 where water jets are used) and zone 2 needs IPX4, so our IP65 models meet both. Have the work done by a qualified electrician.

How many downlights do I need for a room?

As a rough guide on a standard 2.4m ceiling, space them about 1.2 to 1.5m apart and about half that distance from the walls. Brighter fittings or wider beams can go a little further apart.

What size hole do I need?

Each product lists its cut-out in the spec table. Our fire rated models need about 65 to 75mm, so measure existing holes before ordering replacements.

Will my downlights dim?

Most of ours are dimmable or come with a dimmable option, so choose that option at checkout. Check the dimming type on the product: most dim from a mains LED dimmer, some larger models use 0-10V control.