Dimmer Switch for LED Lights: Trailing Edge, Minimum Load and How Many Lamps

10 min read

Living room in the evening with warm white recessed downlights dimmed low and a white rotary dimmer switch on the wall

The short answer

Use a dimmer made for LED with dimmable lamps. Most homes suit a trailing edge dimmer with no minimum load. Compare the dimmer's LED rating, not its headline wattage: a dimmer sold as 400W may take only 100W of LED. Add up the lamp watts on each gang, check any maximum lamp count, and leave some headroom.

Key takeaways

  • Only dimmable lamps on a dimmer, and one lamp model per dimmer.
  • Trailing edge suits most dimmable LED lamps; leading edge suits some lamps and big commercial loads.
  • Read the LED rating. Our V-Pro touch and remote dimmer is 400W for filament lamps but 100W, or 1 to 10 lamps, for LED.
  • With only a few lamps, choose a dimmer with no minimum load, such as Varilight V-Pro.
  • 1-10V drivers and LED strip need their own controller, not a mains dimmer.
On this page
  1. Which dimmer switch for LED lights do you need?
  2. Can you use a dimmer switch on LED lights?
  3. Leading edge vs trailing edge dimmers
  4. Why a "400W" dimmer may only handle 100W of LED
  5. How many LED lamps can you put on one dimmer?
  6. Minimum load: why a few LEDs can be too few
  7. Set the minimum brightness after fitting
  8. Rotary, touch, remote or smart?
  9. Dimming tubes, panels and LED strip
  10. Before you buy: a 6 point check
  11. If you want the short version
  12. Common questions

Which dimmer switch for LED lights do you need?

A dimmer switch for LED lights has to do three things a halogen dimmer never had to: work smoothly with a very small load, suit the electronics inside the lamp, and survive the surge of current LED drivers draw at switch-on. Pick the dimmer by what you are dimming, then check the LED rating, then count the lamps.

What you are dimming Dimmer you need Examples in our range
Dimmable GU10s, bulbs and mains downlights at home Mains LED dimmer, trailing edge, with an LED rating Varilight V-Pro rotary, 1 to 4 gang, 100W to 300W of LED per gang
Large LED loads: panels, rows of downlights, commercial spaces Commercial leading edge dimmer with a high LED rating Varilight V-Com, up to 400W
A dimmer you can work from your sofa Touch and remote dimmer V-Pro touch and remote dimmers with the YRC8 handset, glass touch panels with RF remotes
Panels, tubes and high bays with 1-10V or 0-10V drivers Control dimmer with a 1-10V or 0-10V output, not a mains dimmer Osram DIM MCU, EUCHIPS rotary, KL and T18 glass panels
12V or 24V LED strip Low voltage strip dimmer or controller, or a mains dimmable driver Glass panel strip controllers, TRIAC dimmable strip drivers
Phone or voice control Smart dimmer module Tuya Zigbee TRIAC dimmer with leading or trailing edge by DIP switch

Most homes need the first row. The rest of this guide explains why, and how to stop the common mistakes that cause flicker and buzz.

Can you use a dimmer switch on LED lights?

Yes, if both halves match. The lamp or fitting must be marked dimmable, and the dimmer must be made for LED loads. A dimmable lamp on an old halogen dimmer often flickers or hums. A non-dimmable lamp on any dimmer can flicker, buzz and fail early, even with the knob turned right up.

If you already have flicker or a hum, start with our guide to why LED lights flicker, buzz or glow when off. This guide is about choosing the right dimmer in the first place.

Leading edge vs trailing edge dimmers

Mains dimmers work by chopping part of each half of the AC wave. A leading edge dimmer switches on part way through each half wave. A trailing edge dimmer switches on at the start and off part way through. The difference matters because the small driver inside an LED lamp copes far better with a smooth start than a sudden step.

Trailing edge Leading edge
Also called Reverse phase, MOSFET Forward phase, TRIAC
Best for Most dimmable LED lamps and downlights in homes Lamps and drivers that ask for it, larger commercial LED loads
Noise Usually silent Can hum with some lamps
Ledison examples Varilight V-Pro (trailing edge by default) Varilight V-Com (leading edge, up to 400W)

You do not always have to choose. Our V-Pro dimmers are trailing edge by default with a selectable leading edge mode, called Mode 2, for the few LEDs that prefer it. The glass touch and rotary panels and the Zigbee smart dimmer set leading or trailing edge with a small DIP switch. If a lamp's packaging names a dimming type, follow it.

Why a "400W" dimmer may only handle 100W of LED

This is the mistake behind most dimmer failures. A dimmer's headline wattage is often its rating for old filament lamps. Its LED rating is much lower, because LED drivers draw a sharp surge of current at switch-on and present a different kind of load.

Our Varilight V-Pro touch and remote dimmer shows the gap clearly on one spec sheet: 400W of incandescent lamps, 300W of halogen, but only 100W of LED, or 1 to 10 LED lamps.

One dimmer, three ratings: 400W incandescent, 300W halogen, 100W LED. Eight 5W GU10s use 40W of the 100W LED rating. Varilight V-Pro touch and remote dimmer, one gang Incandescent Halogen LED 8 x 5W GU10 400W 300W 100W, or 1 to 10 LED lamps 40W: well inside the LED rating
Read the LED line, not the headline figure. The same dimmer that handles 400W of filament lamps is rated for 100W of LED.

So when you compare dimmers, compare the LED figure. Our V-Pro range is rated from 100W to 300W of LED per gang depending on the model, and the V-Com KQP401W takes 20W to 400W of LED for bigger commercial jobs.

How many LED lamps can you put on one dimmer?

Add up the watts of every lamp on each gang and keep the total inside the dimmer's LED range. Then check whether the dimmer also gives a maximum number of lamps, because some do.

A worked example

  1. A kitchen has 8 dimmable GU10s at 5W each on one switch. That is 8 x 5W = 40W of LED.
  2. A V-Pro JQP401W is rated 0W to 120W of LED, with no minimum load and no maximum number of lamps. 40W sits comfortably inside it.
  3. A V-Pro JQP303W 3 gang dimmer is rated 0W to 100W per gang, and its spec says 10 LEDs per gang. Eight lamps on one gang is fine; twelve would not be, even though 12 x 5W is only 60W.

Leave yourself some room. A dimmer working close to its limit runs warmer, and if you later swap to brighter lamps the load creeps up. V-Pro dimmers protect themselves: if the load is too high they turn the lights down or off until it is corrected, which can look like a fault.

Drivers and fittings, not just lamps

For downlights with a separate driver, or TRIAC dimmable LED drivers, use the driver's input power or current, not its output. Our glass touch panel dimmer spec says exactly this: work out the maximum number of lamps or drivers from their input power or input current.

Get this right

Compare LED ratings, not headline wattage. Add up the LED watts on each gang, check any maximum lamp count, and leave headroom. Dimmable lamps only, and one lamp model per dimmer.

Minimum load: why a few LEDs can be too few

Many older dimmers need a minimum load before they work smoothly. Four 5W lamps add up to just 20W, which may be below that minimum, so the dimmer never settles and the lamps flicker at the bottom of the range.

Dimmer LED load per gang Dimming type
Varilight V-Pro JQP401W, 1 gang 0W to 120W, no minimum Trailing edge, leading edge mode
Varilight V-Pro JQP303W, 3 gang 0W to 100W, 10 LEDs per gang Trailing edge, leading edge mode
Varilight V-Pro JQP601W, 1 gang 0W to 300W, no minimum Trailing edge
Varilight V-Pro touch and remote, 1 or 2 gang 0W to 100W, 1 to 10 LEDs Leading or trailing edge
Varilight V-Com KQP221W, 1 gang 15W to 220W, max 26 LEDs Leading edge
Varilight V-Com KQP401W, 1 gang 20W to 400W, no maximum number of lamps Leading edge

If you only have two or three lamps on a circuit, a V-Pro with no minimum load is the safe choice. Save the V-Com models for big loads where their higher minimum is never an issue.

Set the minimum brightness after fitting

Even a good dimmer and a good lamp can shimmer at the very bottom of the range. V-Pro dimmers let you set the lowest point the knob reaches, with pushes of the knob, in three steps on many models. Set it once, just above the point where your lamps start to flicker, and the dimmer never goes below it. The V-Com commercial dimmers and the touch and remote dimmers also have an adjustable minimum brightness.

Rotary, touch, remote or smart?

Push on, push off rotary

The most common UK dimmer. Push the knob to switch and turn it to dim. V-Pro rotary dimmers come in 1, 2, 3 and 4 gang, in white, brushed steel, mirror chrome, satin brass and screwless finishes.

Touch and remote

V-Pro touch and remote dimmers dim by touch on the plate or by a handset (the YRC8 remote is sold separately), and can store lighting scenes with Varilight's LightScene remote. Our glass touch panels and rotary glass panels dim from the panel and from compatible RF 2.4GHz remotes.

Smart

The Tuya Zigbee TRIAC dimmer is a compact module that dims dimmable LED lamps from the Tuya app, an RF remote or a push switch, with leading or trailing edge set by DIP switch. App control needs a Zigbee hub, such as our WG-Z gateway. Smart dimmers without a neutral at the switch can make LEDs glow faintly when off, which is covered in our flicker and glow guide.

Two way switching

Most V-Pro rotary dimmers are 2 way, so they work with a standard 2 way switch at the other end of the room or the stairs. Check the product: the satin brass V-Pro models say they work with a standard 2 way switch at the other location but cannot dim from both places.

Dimming tubes, panels and LED strip

A wall dimmer can only dim what the fitting's driver allows. Look at the driver, not just the light.

  • TRIAC dimmable drivers work with a mains LED dimmer. Our Voltacon 40W and 60W constant current drivers set leading or trailing edge with a DIP switch; the Euchips EUP range and Mean Well PCD-25 are also TRIAC dimmable.
  • 1-10V and 0-10V drivers need a control dimmer that sends a low voltage signal on two extra wires. The Osram DIM MCU controls up to 50 dimmable drivers and its push switch turns the mains on and off.
  • LED tubes: our standard T8 and T5 tubes are not dimmable. Our dimmable T8 and T5 tubes run from an external driver, with TRIAC, 1-10V or DALI options, and must never go straight onto the mains.
  • LED strip: dim a 12V or 24V strip with a low voltage controller after the power supply, or with a TRIAC dimmable strip driver on a mains dimmer.
Control signal Wires to the driver What you fit on the wall
TRIAC (phase cut) Switched live and neutral only Mains LED dimmer
1-10V or 0-10V Mains plus a separate pair of control wires 1-10V or 0-10V control dimmer
DALI Mains plus a two-wire DALI bus DALI controller or push switch input

Before you buy: a 6 point check

  1. Check every lamp or fitting is marked dimmable, and note any dimming type it asks for.
  2. Count the lamps on each switch and add up their watts.
  3. Pick a dimmer whose LED rating, not its headline wattage, covers that total with room to spare.
  4. Check any maximum number of lamps per gang.
  5. Match the gangs and the 1 way or 2 way switching you already have.
  6. Measure the back box: most of our Varilight dimmers suit a 25mm box, the screwless models need 35mm.

Safety: when to call an electrician

Swapping a switch for a dimmer means working on a live circuit. Turn the circuit off at the consumer unit and, unless you are competent, ask a qualified electrician. Call one straight away if a dimmer plate gets too hot to touch, crackles or smells of burning. Electrical work in homes in England and Wales falls under Part P of the Building Regulations.

For installers

  • V-Pro JQP401W and JQP601W: 0W to 120W and 0W to 300W of LED, no minimum load, no maximum number of lamps, 25mm back box, BS EN 60669-2-1.
  • V-Pro JQP303W: 3 gang, 0W to 100W per gang, 10 LEDs per gang.
  • V-Com KQP401W: 20W to 400W, leading edge, soft start and thermal cut-out; listed for LED panels, T8 and T5 tubes and downlights on TRIAC dimmable drivers.
  • Screwless JDQP401S: 120W LED, needs a 35mm back box, must be earthed.
  • Osram DIM MCU: 1-10V, 40mA control output, up to 50 drivers, 6A switching contact, 4-core cable (L, N, control +, control -). Never connect mains to the control pair.

If you want the short version

Use dimmable lamps and a dimmer made for LED. Compare the LED rating, add up the watts, check any lamp count and leave headroom. Trailing edge suits most homes; leading edge suits big commercial loads. For 1-10V drivers and LED strip, fit the controller that matches the driver, not a mains dimmer.

Products that help

See all LED Dimmer Switches · See all AC Dimmable Power Supplies · See all LED Drivers 1-10V · Why Are My LED Lights Flickering, Buzzing or Glowing When Off? · LED Drivers Explained: Constant Voltage vs Constant Current, and How to Size One · DALI Lighting, 0-10V and 1-10V Dimming Explained for Installers

Common questions

Can you use a dimmer switch on LED lights?

Yes, if the lamps are marked dimmable and the dimmer is made for LED loads. Non-dimmable lamps on a dimmer can flicker, buzz and fail early.

What is the difference between leading edge and trailing edge dimmers?

A leading edge dimmer switches on part way through each half of the mains wave; a trailing edge dimmer switches off part way through. Trailing edge is gentler on LED drivers and usually silent, so it suits most dimmable LED lamps.

How many LED bulbs can I put on a dimmer switch?

Add up the lamp watts on each gang and keep inside the dimmer's LED rating, with some room to spare. Some dimmers also set a maximum number of lamps, such as 10 per gang on the V-Pro JQP303W, so check both.

Why does my 400W dimmer flicker with only a few LED lamps?

The 400W figure is usually for filament lamps, and many older dimmers also need a minimum load that a few LEDs do not reach. Fit an LED dimmer with no minimum load and check its LED rating.

What is the best dimmer switch for LED lights with no flickering?

One rated for LED, trailing edge by default, with no minimum load and an adjustable minimum brightness, used with dimmable lamps of one model. Our Varilight V-Pro dimmers have all four.

What back box depth do I need for a dimmer switch?

Most of our Varilight dimmers fit a 25mm deep back box. The screwless V-Pro models need 35mm, so check the product details before you order.

How do I dim LED strip lights or 1-10V panels?

LED strip dims with a low voltage controller after the power supply, or with a TRIAC dimmable driver on a mains LED dimmer. 1-10V and 0-10V drivers need a 1-10V or 0-10V control dimmer such as the Osram DIM MCU.