Why Are My LED Lights Flickering, Buzzing or Glowing When Off?

7 min read

Modern kitchen at dusk with a row of recessed LED downlights and a rotary dimmer switch on the wall

The short answer

Most LED flicker and buzz comes from the dimmer, not the lamp: an old dimmer built for halogen, a load too small for its minimum, or the wrong dimming mode. Glowing when off is usually a small current leaking through an illuminated or smart switch, or induced in long switch cables. Steady flicker at full brightness points to a failing lamp, a loose connection or a 12V transformer the LED cannot work with.

Key takeaways

  • Flicker only when dimmed: check the dimmer is LED rated, trailing edge, and that your LED load sits inside its LED range.
  • Flicker at full brightness with no dimmer: suspect one failing lamp, a loose lampholder or terminal, or a halogen transformer on 12V MR16s.
  • Buzzing: usually a leading edge dimmer or a cheap lamp driver. A trailing edge LED dimmer normally cures it.
  • Faint glow when off: a tiny leakage current, often from an illuminated, smart or two-way switch arrangement. It is common, but have the switching checked if you are unsure.
  • Burning smell, a hot dimmer plate or flicker across the whole house: switch off and call an electrician.
On this page
  1. First, which problem have you got?
  2. Why do LED lights flicker when they are dimmed?
  3. Why are my LED lights flickering at full brightness?
  4. Why do LED lights buzz?
  5. Why do LED lights glow when switched off?
  6. A 10 minute check you can do yourself
  7. If you want the short version
  8. Common questions

First, which problem have you got?

LED lights flickering, buzzing or glowing when off can look like one problem, but they have different causes. Find your symptom in the table, then jump to that section.

What you see or hear Most likely cause Usual fix
Flicker only when dimmed down Dimmer not suited to LED, or the LED load is below its minimum LED rated trailing edge dimmer, raise the minimum brightness setting
Flicker at full brightness, no dimmer One failing lamp, a loose connection, or a 12V halogen transformer Swap the lamp, check the lampholder, fit an LED driver
Lights dip when the kettle or shower goes on Voltage dips on the supply Have an electrician check the circuit and supply
Hum from the switch or the lamps Leading edge dimmer, or a lamp driver that does not like being dimmed Trailing edge dimmer and good quality dimmable lamps
Faint glow or a blink when switched off Leakage current through an illuminated, smart or two-way switch arrangement Standard switch, a smart switch with a neutral, or a load capacitor fitted by an electrician

Why do LED lights flicker when they are dimmed?

Because most dimmers on UK walls were made for halogen bulbs. A 50W halogen lamp is an easy load for a dimmer. A 5W LED lamp has a small electronic driver inside it, and the dimmer has to keep that driver happy at a fraction of the power it was built for.

The dimmer is leading edge

A mains dimmer works by switching off part of each half of the AC wave. A leading edge dimmer cuts the start of each half wave; a trailing edge dimmer cuts the end. Most dimmable LED lamps are designed for trailing edge, which gives a softer switch-on, less flicker and less noise.

Leading edge dimming cuts the start of each half wave; trailing edge dimming cuts the end Leading edge Trailing edge switches on part way through switches off part way through
Orange is the part of each half wave that reaches the lamp. Leading edge dimmers switch on with a sudden step, which LED drivers often answer with flicker and hum. Trailing edge dimmers start smoothly and switch off instead.

The LED load is below the dimmer's minimum

Many older dimmers need a minimum load, often 40W to 60W, before they work smoothly. Four 5W GU10s add up to 20W, so the dimmer never settles and the lamps flicker, especially at the bottom of the range. Check the dimmer's LED rating, not its halogen rating, and add up the LED watts on each gang. Our Varilight V-Pro dimmers have no minimum load and are trailing edge by default, with a leading edge mode for the few lamps that need it.

The bottom of the dimming range is set too low

Even with the right dimmer, some lamps cannot hold a steady light at the very bottom of the range. Good LED dimmers let you raise the minimum brightness so the knob never goes below the point where the lamps start to shimmer. On V-Pro dimmers this is a three-step setting.

Lamps are mixed

Different lamp models respond to the same dimmer signal in different ways. Put one brand and model on each dimmer. If you add a single new lamp and every light on the circuit starts to flash, take the new lamp out first.

Get this right

Dimmable lamp, LED rated dimmer, total LED watts inside the dimmer's LED range, and one lamp model per dimmer. Get those four right and most dimming flicker goes away.

Why are my LED lights flickering at full brightness?

If there is no dimmer, or your LED bulbs or downlights flicker even at full brightness, look at these in order.

  1. One failing lamp. The small driver inside an LED lamp ages, faster in hot, enclosed fittings. A lamp that flickers, strobes or takes a second to come on is often near the end. Swap it with a lamp from another fitting: if the fault follows the lamp, replace the lamp.
  2. A loose connection. If the fault stays in the same fitting, the lampholder or a terminal may be loose. Turn the circuit off at the consumer unit before you touch anything, and if a connection needs remaking, ask an electrician.
  3. A 12V transformer. MR16 spotlights run at 12V from a transformer. Most halogen transformers are electronic and need a minimum load, often 20W or more. A few LED MR16s draw far less, so the transformer keeps cutting in and out. Replace it with a 12V LED driver sized for the LED load.
  4. Voltage dips. If lights dip or flicker when a kettle, shower or heater switches on, the supply voltage is dropping under load. LEDs show this more than halogen did. If it happens across the whole house, ask an electrician to check the circuit and, if needed, your network operator.

Why do LED lights buzz?

Buzzing usually comes from the dimmer, the lamps, or both. A leading edge dimmer switches on with a sharp step in every half wave, a hundred times a second, and parts inside the dimmer or the lamp driver vibrate at that rate. Switching to a trailing edge LED dimmer normally cures it. If the hum comes from the lamps themselves, try a better quality dimmable lamp, and keep the dimmer loaded within its LED range: a dimmer close to its limit runs hotter and louder.

A quiet hum from a dimmer is not unusual. A dimmer plate that is too hot to keep your hand on, a crackle or a burning smell is not normal: switch the circuit off and call an electrician.

Why do LED lights glow when switched off?

A halogen bulb needs a lot of power to glow, so a few milliamps leaking through a switch never showed. An LED lamp can glow faintly, or blink every few seconds, on that tiny current. Three things cause it.

  • Illuminated or smart switches without a neutral. The little light in the switch, or the electronics in a smart switch, power themselves by letting a small current through the lamp when it is off.
  • Long two-way switch cables. In two-way and intermediate switching, long runs of cable next to each other can pass a small current between them, enough to make a sensitive LED glow.
  • A switch in the neutral. If the switch has been wired in the neutral instead of the live, the lamp still has live at it when switched off. This is the one that matters for safety, because the fitting is live even with the light off.

Fixes depend on the cause: a standard switch instead of an illuminated one, a smart switch that uses a neutral, or a small load capacitor fitted at the light by an electrician. If you are not sure which way the circuit is wired, ask an electrician to check it before you change lamps or fittings.

A 10 minute check you can do yourself

  1. Note exactly when it happens: dimmed only, all the time, when another appliance starts, or when off.
  2. Check every lamp on the circuit is marked dimmable if there is a dimmer.
  3. Check every lamp is the same model. Remove any odd one out.
  4. Add up the LED watts per dimmer gang and compare with the dimmer's LED rating.
  5. Swap a flickering lamp with a good one to see whether the fault follows the lamp.
  6. If the dimmer has a minimum brightness setting, raise it one step.
  7. For 12V MR16s, find the transformer and check whether it is an LED driver or a halogen transformer.

Switch off at the consumer unit before removing any fitting, and leave wiring work to a qualified electrician.

Safety: when to call an electrician

Call an electrician if a dimmer or fitting gets hot, crackles or smells of burning; if lights flicker across the whole house; if you suspect the switch is in the neutral; or if any fix needs wiring changed. Electrical work in homes in England and Wales falls under Part P of the Building Regulations.

For installers

  • Varilight V-Pro: trailing edge by default with a leading edge mode, no minimum load, LED ratings from 100W to 300W per gang depending on model, minimum brightness adjustable in three steps.
  • V-Com: leading edge, for larger commercial LED loads up to 400W.
  • 1-10V and 0-10V drivers need a matching control dimmer, not a mains dimmer.
  • Ghosting: check for a neutral at the switch before fitting smart or illuminated switches on LED circuits.

If you want the short version

Dimmed flicker and buzz: fix the dimmer. Full brightness flicker: find the lamp, the connection or the transformer. Glow when off: find the leakage, and make sure the switch is in the live. If anything gets hot or smells, stop and call an electrician.

Products that help

See all LED Dimmer Switches · See all LED Downlights · See all GU10 Spot Lights 230V · Dimmer Switch for LED Lights: Trailing Edge, Minimum Load and How Many Lamps · How to Replace Halogen Downlights with LED: GU10, MR16 and Transformers · LED Drivers Explained: Constant Voltage vs Constant Current, and How to Size One

Common questions

Why do my LED lights flicker when dimmed but not at full brightness?

The dimmer is struggling to control a small LED load. Older dimmers were made for halogen and need a minimum load that a few LED lamps do not reach. Fit an LED rated trailing edge dimmer and keep the total LED wattage within its LED range.

Why does one LED bulb flicker and the others don't?

Usually that lamp or its lampholder. Swap it with a lamp that works; if the flicker moves with the lamp, replace the lamp. If it stays in the same holder, the holder or its connection needs checking.

Why do all my lights flash when I add one new bulb?

Mixing lamp brands or models on one dimmer can upset how the dimmer reads the load. One unsuitable or faulty lamp can make every lamp on the circuit flash. Remove it and fit the same model as the rest.

Is it dangerous if LED lights glow when switched off?

A faint glow from leakage current is common and usually harmless, but it can also mean the switch is in the neutral rather than the live, which is not safe. If you are not sure how the circuit is wired, ask a qualified electrician to check it.

Can I use a non-dimmable LED bulb on a dimmer switch?

No. Even at full brightness a dimmer can make a non-dimmable lamp flicker, buzz or fail early. Use lamps marked dimmable, or replace the dimmer with a standard switch.

Why do my 12V MR16 LEDs flicker?

Most halogen transformers are electronic and need a minimum load, often 20W or more. A few LED MR16s draw far less, so the transformer cuts in and out. Replace it with a 12V LED driver sized for the LED load.

Do LED lights flicker when they are about to fail?

Often, yes. The driver inside a lamp ages, especially in hot, enclosed fittings, and flicker or a slow start is a common early sign. Replace the lamp, and check the fitting is suitable for the lamp's heat.