Garage Lighting Guide: LED Battens, Lumens and How Many You Need

11 min read

Tidy UK single garage with a car, a workbench and two linear LED battens on the ceiling in natural white light

The short answer

For most UK garages, fit LED battens or IP65 tri-proof fittings on the ceiling in natural or cool white, in rows either side of the car. A single garage used for parking needs about 4,500 lumens, a DIY space about 9,000 and a proper workshop about 15,000, with an extra light over the bench. Use sealed fittings if the garage is damp or unheated, and fix loft lights high with a switch by the hatch or a sensor.

Key takeaways

  • Lumens needed = target lux x floor area in m² ÷ 0.6. About 150 lux to park, 300 for DIY, 500 for a workshop.
  • Use IP20 battens in dry, heated garages and IP65 tri-proof fittings anywhere damp, dusty or unheated.
  • Two fittings either side of the car beat one bright fitting in the middle, and keep them clear of an up and over door.
  • Choose 4000K for mixed use, 5000K to 6000K for car work, and CRI 90 or above for paint and colour matching.
  • Lofts need about 100 lux, fittings fixed high and clear of insulation, and a switch by the hatch or a sensor.
On this page
  1. Good garage lighting in one paragraph
  2. How many lumens does a garage need?
  3. Which LED fitting is best for a garage?
  4. How many LED battens do I need for a garage?
  5. What is the best lighting for a garage workshop?
  6. Loft lighting: how to light a loft properly
  7. A quick checklist before you buy
  8. The short version
  9. Common questions

Good garage lighting in one paragraph

Good garage lighting is bright, even and shadow free, and it survives cold, damp and the odd knock from a ladder. For most UK garages that means LED battens or tri-proof fittings on the ceiling, in natural white (4000K) or cool white (5000K to 6000K), set out in rows either side of where the car sits. A single garage used for parking needs about 4,500 lumens. Use it as a workshop and you want about twice that, plus extra light over the bench. Lofts need less light but more thought about switching, and the rest of this guide covers both.

Jump to what you need:

How many lumens does a garage need?

Work it out from the floor area and the job you do there. Light on a surface is measured in lux, which is lumens per square metre. Not every lumen from a fitting reaches the floor: some is absorbed by walls, shelving and the ceiling, more so in a garage with bare block walls than in a white painted room. A simple way to allow for this is to divide by 0.6.

Lumens needed = target lux x floor area in m² ÷ 0.6

Most US guides quote "lumens per square foot", which is the same idea in older units. For UK garages, these targets work well in practice:

How you use the space Target on the floor or bench Single garage (3 x 6m, 18m²) Double garage (6 x 6m, 36m²)
Parking, bins, bikes, storage About 150 lux About 4,500 lm About 9,000 lm
General DIY, car cleaning, gym About 300 lux About 9,000 lm About 18,000 lm
Workshop, car repairs, woodwork About 500 lux About 15,000 lm About 30,000 lm
Fine work at the bench only About 750 lux on the bench General light as above, plus a fitting over the bench

These are design targets, not legal minimums. If your walls are painted white, you can go a little lower. If the garage is full of dark shelving or the walls are bare brick, go a little higher. LED is easy to overlight, so if you are unsure, choose fittings with a power or colour switch, or put the bench light on its own switch.

Get this right

Count lumens, not watts. A 40W LED batten can give anywhere from about 3,000 to 5,000 lumens depending on the model, so compare the lumen figure on each listing and add them up against the table above.

Which LED fitting is best for a garage?

A linear fitting on the ceiling: a batten in a dry, heated garage, a tri-proof fitting anywhere damp, dusty or unheated. Long fittings spread light along the length of the car and down the sides, which is what stops you working in your own shadow.

Fitting Best for Watch out for
LED batten (IP20) Dry, insulated garages, lofts, utility rooms, home gyms Not sealed against damp, dust or water spray
Tri-proof fitting (IP65) Unheated or damp garages, workshops with dust, car washing, outbuildings Heavier, so fix into joists or proper anchors
Slimline batten Low ceilings, lofts, linked runs, sensor and emergency versions Indoor and dry only
Vapour proof, non-corrosive fitting Car washing areas, stables, damp outbuildings Bigger body than a batten
LED tubes in an existing fitting Keeping a sound fluorescent fitting Old fittings may need the ballast removed or bypassed
Panels or downlights Plastered garage conversions with a flat ceiling Harder to fit on joists and boarding, and less light along the walls

Cold and damp

Fluorescent tubes are slow and dim when they are cold, which is why so many garage lights flicker for a minute on a winter morning. LED starts at full brightness straight away. Check two figures in the spec table. The operating temperature tells you how cold the fitting can work: our Voltaled Uranus battens list minus 20°C to 45°C and our 4ft tri-proof minus 25°C to 50°C. The IP rating tells you how well it is sealed. IP20 means indoor and dry. IP65 means dust tight and protected against water jets, which suits a garage that gets damp or where you wash the car or hose the floor.

Knocks and dust

Ladders, timber and footballs all find the garage light in the end. A polycarbonate diffuser does not shatter the way an old glass or acrylic one can, and a sealed IP65 body keeps sawdust out of the electronics. Our 2ft, 4ft and 5ft tri-proof fittings list an IK08 impact rating on their datasheets.

Keeping your fluorescent fittings

If the old twin fluorescent fittings are sound, LED tubes are the quickest change. Our standard T8 tubes come with an LED starter for switch-start fittings. Fittings with electronic ballasts need the ballast removed or bypassed, which is a job for an electrician. If the fitting is old, yellowed or cracked, a new batten usually costs less in time than converting it.

How many LED battens do I need for a garage?

Divide the lumens you need by the lumens of one fitting, round up, then set them out in rows. Here is how that works with real fittings from our range.

Fitting (from our range) Light output Single garage, 150 lux (4,500 lm) Single garage, 300 lux (9,000 lm) Double garage, 300 lux (18,000 lm)
Uranus batten 4ft 40W, IP20 3,450 lm 2 3 6
Tri-proof 4ft 40W, IP65 4,800 lm 1 to 2 2 4
Tri-proof 5ft 65W, IP65 7,800 lm 1 2 3
Cyrus 5ft, power switch 25W, 50W or 60W 3,000, 6,000 or 7,200 lm 2 at 25W 2 at 50W 3 at 60W

One bright fitting in the middle of the ceiling is the classic mistake. The car roof blocks it, and you end up working on the wheels and the sides of the car in shadow. Two fittings with the same total output, set either side of the car, light the floor, the doors and the walls far better.

Plan of a single garage, 3 by 6 metres, door on the left, with two battens running along the length either side of the car and a third across the back wall over the workbench 6m 3m car workbench on the back wall batten 1 batten 2 about 0.75m garage door bench light, own switch
Plan of a typical single garage. Two battens run along the length, about 0.75m in from each side wall, so light reaches both sides of the car. A third fitting over the workbench, on its own switch, gives task light without overlighting the whole space. Keep fittings clear of the path of an up and over door when it is open.

Layout rules that work

  • Run fittings along the length of the garage, not across it, so light falls down the sides of the car.
  • Keep the rows about 0.5m to 1m in from the side walls. That lights the walls and anything on them, and the gap between rows covers the middle.
  • Check the door. An up and over door swings up into the garage. Measure where it sits when open and keep fittings clear of it, or the door will hit them or block their light.
  • Link fittings into one run in a double garage or workshop. Our Uranus battens link up to 20 units, our 4ft tri-proof up to 16 and our 5ft tri-proof up to 10, which saves a separate cable to each fitting.

What is the best lighting for a garage workshop?

Bright general light from linear fittings, a colour around 4000K to 5000K, a good colour rendering index (CRI), and a separate light over the bench.

Colour temperature

Natural white (4000K) is the safe choice for a workshop you spend hours in: it is crisp without feeling clinical. Cool white (5000K to 6000K) suits a space used mainly for car work, cleaning and inspection. Warm white (3000K) belongs in a garage converted into a gym, office or games room. Many of our fittings let you choose after fitting: the Uranus battens come in 3000K, 4000K or 5500K, the slimline battens switch between 3000K, 4000K and 5000K, and the Cyrus 5ft colour switch version lets you pick on site.

CRI for paint, wiring and wood

CRI tells you how true colours look under the light, on a scale up to 100. Most of our battens are CRI above 80, which is fine for general work. If you match paint, check wire colours or finish wood, look for CRI 90 or above: the Cyrus 5ft power and colour switch fitting is listed at Ra above 90.

Flicker and rotating tools

Cheap LED fittings with poor drivers can flicker at mains frequency, which you may not notice until you look at a spinning chuck or saw blade. Choose fittings with a quality driver, and if your lights already flicker, see our guide on why LED lights flicker, buzz or glow.

Sensor lights for garages you walk through

If you walk through the garage to the house with your hands full, a sensor saves fumbling for the switch. Our microwave sensor T8 tubes dim to a 20% standby level when nobody is there and come up to full when you walk in, and our slimline battens come in PIR sensor versions. For a workshop, think twice: a sensor that switches off while you stand still at the bench is annoying, so keep a manual switch for the work lights.

Loft lighting: how to light a loft properly

Lofts need less light than a workshop, but fittings must be fixed securely, kept clear of insulation, and switched where you can reach them from the hatch. For a boarded loft used for storage, aim for about 100 lux across the boarded area. A typical boarded area of 4 x 6m (24m²) under bare timber, which reflects little light, needs about 4,000 to 5,000 lumens. That is two Uranus 4ft battens at 3,450 lumens each, or four 2ft slimline battens at 1,200 lumens each if you want a slimmer fitting on the rafters.

Where to fit them

Fix fittings along the ridge or high on the purlins, running the length of the boarded area, so light falls on both sides and not just the walkway. Do not bury fittings or cables in loose insulation, keep cables clipped to timbers clear of where you step and stack boxes, and use a junction box rated for the job where you join into an existing circuit. A slim batten is easier to fix to a rafter than a deep fitting, and our slimline battens are only 50mm wide and 55mm deep.

Switching: switch by the hatch, pull cord or sensor

  • A switch on the landing by the hatch, ideally with a neon or indicator, so you can see from below that the loft light is on.
  • A motion sensor fitting that switches on as you climb in. Our boarded loft project with Access4lofts used PIR sensor battens fed from an existing ceiling circuit, so the lights come on as soon as the ladder comes down, with no switch at all.
  • Emergency versions. Our 5ft slimline batten has an emergency version with 3 hours of light if the power fails, which is useful if you would otherwise be stuck in a dark loft at the top of a ladder.

Safety: when to call an electrician

Garages, outbuildings and lofts often need a new circuit, a supply run out to a detached garage, or a connection into an existing lighting circuit. In England and Wales some of this work is notifiable under Part P of the Building Regulations, and a detached garage supply needs the right cable, protection and earthing. Ask a qualified electrician to design and fit new circuits, and always isolate the circuit at the consumer unit before touching a fitting. If your garage still has old fluorescent fittings with electronic ballasts, have the ballast removed or bypassed by an electrician before fitting LED tubes.

A quick checklist before you buy

  1. Measure the floor area and decide what you use the space for: parking, DIY or workshop.
  2. Work out the lumens: target lux x area in m² ÷ 0.6.
  3. Choose IP20 battens for dry, heated spaces and IP65 tri-proof fittings for anywhere damp, dusty or unheated.
  4. Pick 4000K for a mixed use space or 5000K to 6000K for car work, and CRI 90 or above for colour matching.
  5. Plan two or more rows along the length, clear of the garage door when it is open.
  6. Decide on switching: wall switch, sensor, or both, and a separate switch for the bench.
  7. Check how many fittings link in one run and plan the cable route.

For installers

  • Voltaled Uranus battens: 2ft 20W 2,000 lm, 3ft 30W 2,600 lm, 4ft 40W 3,450 lm; IP20; 3000K, 4000K or 5500K; surface or suspended; dimmable option; link up to 20 units; minus 20°C to 45°C.
  • Tri-proof fittings: 2ft 20W 2,400 lm, 3ft 30W 3,900 lm, 4ft 40W 4,800 lm, 5ft 65W 7,800 lm (Poseidon); IP65; IK08 and Class I on the 2ft, 4ft and 5ft datasheets; stainless brackets; through wiring 3 x 1.5mm or 2.5mm; link 16 (4ft) or 10 (5ft); optional microwave sensor and 3 hour emergency module.
  • Slimline battens: 50 x 55mm section, 3000K, 4000K or 5000K selectable, 20mm knockout in the end cap on the 5ft models; 5ft 30W in standard, PIR sensor or 3 hour emergency versions.
  • Microwave sensor T8 tubes: 4ft 20W 2,100 lm and 5ft 22W; 4000K; 2-step dimming with 20% standby; mounting height 2.5m to 10m.

The short version

Work out lumens from the floor area and the job: about 4,500 lumens to park in a single garage, about 9,000 for DIY, about 15,000 for a proper workshop. Use battens in dry, heated garages and IP65 tri-proof fittings anywhere damp or cold. Put two rows along the length, either side of the car and clear of the door, add a bench light on its own switch, and choose 4000K or 5000K with a good CRI. In the loft, fix fittings high, keep them clear of insulation, and switch them from the hatch or with a sensor. Leave new circuits and outbuilding supplies to an electrician.

Products that help

See all LED Batten Uranus · See all LED Tri-Proof Lights · See all Slimline Linear LED Fitting · LED High Bay Lighting: UFO vs Linear, Lux Levels and Payback for Warehouses · How to Replace a Fluorescent Tube with LED: the Ban, Starters and Ballast Bypass · Emergency Lighting Explained: Maintained vs Non-Maintained, Testing and the Rules

Common questions

How many lumens do I need for a garage?

Multiply the target lux by the floor area in square metres and divide by 0.6. A single garage of about 18m² needs about 4,500 lumens for parking, 9,000 for DIY and 15,000 for a workshop.

What is the best lighting for a garage ceiling?

Linear LED fittings: battens in a dry, heated garage, IP65 tri-proof fittings in a damp, dusty or unheated one. Run them along the length of the garage, either side of the car.

How many LED battens do I need for a double garage?

For general DIY use at about 300 lux, a 36m² double garage needs about 18,000 lumens: six 4ft battens at 3,450 lumens or three 5ft tri-proof fittings at 7,800 lumens.

Is 4000K or 6000K better for a garage?

4000K natural white suits a garage you spend long hours in. 5000K to 6000K cool white suits car work, cleaning and inspection. Warm white is better for a garage converted into a living space.

Do LED lights work in a cold garage?

Yes. Unlike fluorescent tubes, LED starts at full brightness in the cold. Check the operating temperature in the spec table: our Uranus battens list minus 20°C and our 4ft tri-proof minus 25°C.

Do I need an IP rated light in a garage?

In a dry, heated garage IP20 is fine. If it gets damp, dusty or unheated, or you wash the car inside, use IP65.

How should I switch loft lights?

A switch on the landing by the hatch, ideally with an indicator, or a motion sensor fitting that comes on as you climb in. Ask an electrician to connect into the lighting circuit.