Under Cabinet Lighting for Kitchens: Strips, T5 Links and How to Wire Them
9 min read
The short answer
Kitchen under cabinet lighting comes as LED strip in a profile, linkable T5 fittings, low voltage plug-in kits or rechargeable lights. Strip gives the best continuous line but needs a driver and planned wiring. T5 bars and plug-in kits are quickest. Fit the light near the front of the cabinet, match its colour to the ceiling, and power it from a socket, a fused spur or the lighting circuit.
Key takeaways
- LED strip in a profile gives the neatest line; linkable T5 and plug-in kits are the quickest fit.
- Fit lights near the front of the cabinet underside, hidden by the pelmet, to light the whole worktop.
- Match the colour to the ceiling lights, or go one step cooler.
- Power from a socket (plug-in), a switched fused spur or the lighting circuit; fixed wiring needs an electrician.
- Keep the driver ventilated and reachable, and use sealed IP65 or better strip for plinths.
On this page
- Under cabinet lighting: the four options
- LED strip or linkable T5 under cabinet lights?
- Plug-in kits and rechargeable lights
- Where to fit under cabinet lights
- Warm white or natural white under cabinets?
- How to wire under cabinet lighting
- Kitchen plinth lights
- Replacing old Wren, Magnet or halogen under cabinet lights
- Under cabinet lighting checklist
- If you want the short version
- Common questions
Under cabinet lighting: the four options
Kitchen under cabinet lighting comes in four types: LED strip in an aluminium profile, linkable T5 fittings, low voltage plug-in kits, and rechargeable battery lights. Strip gives the neatest continuous line and suits a refit. T5 and plug-in kits are the quickest to fit to an existing kitchen. Battery lights need no wiring at all. Choose by how much wiring you can do, not just by looks.
| Type | Power | Look | Wiring | Best for |
|---|---|---|---|---|
| LED strip in a profile | 12V or 24V driver, hardwired or plug-in | Continuous, even line; dot-free with a diffuser | Most work: driver, cables, often an electrician | New kitchens, refits, long runs, plinths |
| Linkable T5 fittings | Mains 230V, driver built in | Slim bars, small gap between units | Plug in, or wired by an electrician | Replacing old fluorescent or halogen fittings |
| Plug-in LED kits | 12V adaptor from a socket | Short bars joined with link cables | Plug in, no wiring | Quick upgrades, rented homes |
| Rechargeable lights | Battery, charged by USB | Single bars, often with a motion sensor | None: stick or magnet on | Cupboards, no socket nearby, short bursts of light |
LED strip or linkable T5 under cabinet lights?
LED strip gives the best result: one continuous line of light along the whole run of cabinets, with no gaps at the cabinet joins. It needs a separate driver, careful planning of where the cables go, and an aluminium profile so the dots do not reflect in a glossy worktop. Strip is also the only practical choice for plinth lighting.
Linkable T5 fittings are slim bars with the driver built in. Our plug-in T5 under cabinet lights come in 300mm (4W) and 549mm (9W) lengths, each with its own on/off switch, a frosted cover and a 1m mains cable with a UK plug. You can link up to three of the same type together. They are the easiest swap for old fluorescent under-cabinet tubes.
The trade-off: T5 bars leave a short dark gap between fittings and at the ends; strip does not. T5 bars are faster to fit and need no separate driver. Note that our T5 fittings are for dry indoor rooms and must not be used with dimmers or electronic switches.
Plug-in kits and rechargeable lights
A plug-in kit is the middle way. Our 12W under cabinet kit has three 4W strips, each 280mm long and only 12mm thick, with link cables, 3M tape, screws and a 12V adaptor with a UK plug. Touch the light to dim it. The housing is fully enclosed, with no exposed electrical parts. There is also a version with a PIR motion sensor for wardrobes and cupboards.
Rechargeable lights are the answer when there is no socket nearby and no way to run a cable. They are made for short bursts of light, usually with a motion sensor. Our 60.5cm LED Blade charges by USB in about 3 hours, switches on by itself when it detects movement in low light, and stays on for 18 to 20 seconds. With the sensor switched off it runs for around 2.5 hours. That makes battery lights good for cupboards and larders, but not for lighting a worktop while you cook.
Get this right
If you want worktop light while you cook, choose mains or plug-in lighting. Battery lights with motion sensors are made to come on for seconds at a time, and they need charging. They are ideal inside cupboards, not as the main kitchen task light.
Where to fit under cabinet lights
Fit the light towards the front of the cabinet underside, behind the lip or pelmet. From there it lights the whole depth of the worktop, including the front edge where you chop and prepare food. The lip hides the light source from your eyes when you stand at the counter.
- Glossy worktops and splashbacks reflect the light source. Use a profile with a frosted or opal diffuser so the reflection is a soft line, not a row of dots.
- Corner units look best with a corner profile at 45 degrees, which throws the light down and back at once.
- Over a hob leave the cooker hood's own light to do the job. Heat and steam above a hob shorten the life of strip and adhesive.
Warm white or natural white under cabinets?
Match your ceiling lights. If the ceiling is 3000K, a 3000K strip under the cabinets looks deliberate; a 6000K strip looks like a mistake. If you want a crisper light on the worktop, go one step up to 4000K and no further. Our 300mm plug-in T5 comes in 3000K, 4000K or 5500K, the 549mm T5 and the touch dimmable kit are 4000K, and our strips come in warm, natural and cool white.
For food prep, a high CRI strip makes ingredients look natural. Our 24V 18W per metre strip is RA over 90.
How to wire under cabinet lighting
There are three ways to power under cabinet lights, from easiest to most permanent:
- Plug into a socket. Plug-in T5 fittings and kits come with a UK plug. Many kitchens have a socket in a cabinet above the units or behind an appliance for this. No electrician needed.
- From a fused connection unit (fused spur). A switched fused spur on the worktop wall, wired from the ring or a radial circuit, feeds a driver or the T5 fittings. You get a proper wall switch, and the fuse protects the small cables beyond it.
- From the lighting circuit. The driver is fed from the lighting circuit, so the under cabinet lights switch with the room or from their own switch on the lighting circuit.
Where to hide the driver
The driver needs air and access. Good places are on top of the wall cabinets behind the cornice, inside a cabinet in a small enclosure, or in the void above an extractor run. Never seal it behind a fixed panel or tiles, never bury it in insulation, and keep it away from the heat above the hob. A slim driver such as our 24V 40W Triac dimmable model, 107.5 x 43.5 x 32mm, fits on a cabinet top easily.
Size the driver at the total strip watts plus 20%. For example, 3m of 12W per metre strip is 36W, plus 20% is 43W, so a 48W driver. For more on drivers, voltage drop and profiles, see our strip lights range, which includes a driver calculator.
Safety: when to call an electrician
Plugging a kit into a socket is fine to do yourself. Fitting a fused spur, wiring a driver into a circuit, or running new mains cable to the cabinets is a job for a qualified electrician. In England and Wales, fixed electrical work in homes falls under Part P of the Building Regulations, and a new circuit is notifiable. Switch off at the consumer unit before you remove any existing fitting.
Kitchen plinth lights
Plinth lights sit in the kick board at floor level and give the units a floating look, plus a soft night light for the kitchen. Use LED strip for an unbroken line. Because floors get mopped and spills run under the units, choose a sealed strip, IP65 or better, in a profile fixed to the underside of the cabinet base, shining down onto the floor rather than out into the room. Keep the driver up in a cabinet, not down at floor level, and run low voltage cable down to the plinth.
Our silicone tube strip is IP67 and rated for indoor and outdoor use including damp rooms. Plinth lights look best dimmed, so use a dimmable driver, and link them to their own switch so they can stay on at night.
Replacing old Wren, Magnet or halogen under cabinet lights
Many fitted kitchens came with their own under cabinet lights on a small proprietary driver, often 12V, with special plugs. When one fails you have two choices:
- Like for like. Read the label on the driver for its voltage and whether it is constant voltage. If you can match the voltage and the connector, a new LED fitting may run from it, though old halogen transformers often cause flicker with LED loads.
- Replace the system. Take out the old driver and fittings and fit strip in profiles with a new driver, or plug-in T5 bars. This is usually the better result and avoids mixing old and new.
If you swap old 12V halogen pucks for LED and they flicker, the old transformer is the likely cause; our guide to why LED lights flicker explains why. Old fluorescent under cabinet tubes can come out completely; linkable T5 LED fittings are the simplest replacement.
Under cabinet lighting checklist
- Measure the length under each cabinet and note the corners and the hob.
- Choose the type: strip, T5, plug-in kit or rechargeable.
- Match the colour temperature to the ceiling lights, or one step cooler.
- Decide the power: socket, fused spur or lighting circuit.
- Pick a driver location with air and access, and size the driver with 20% headroom.
- Choose profiles with a diffuser if the worktop or splashback is glossy.
- Book an electrician for any fixed wiring.
For installers
- T5 under cabinet, 549mm 9W: 230V, driver in the lamp holder, 4000K, CRI80, integrated switch, link up to 3, 15cm linking cable, fixing holes about 200mm apart, dry rooms only, not for dimmers.
- T5 under cabinet, 300mm 4W: as above, 3000K, 4000K or 5500K, CRI over 80, PF 0.9.
- 12W touch dimmable kit: 3 x 4W, 1200 lm total, 4000K, 12V adaptor with UK and EU plug, strips 280 x 24 x 12mm.
- Glacial 24V 40W Triac driver: 5% to 100% dimming from leading or trailing edge dimmers, IP65 potted.
If you want the short version
For a new or refitted kitchen, use 24V LED strip in profiles near the front of each cabinet, fed from a driver you can reach, wired by an electrician. For a quick upgrade, plug-in T5 bars or a 12V kit. For cupboards with no power, a rechargeable motion sensor light. Match the colour to the ceiling, hide the driver with air around it, and use sealed strip for plinths. Browse our under cabinet lights, strip drivers and aluminium profiles.
Products that help
Plug-In LED Under Cabinet Light T5 549mm 9W
From £24.95
LED Under Cabinet Lighting Kit 12W
From £33.99
Rechargeable LED Under Cabinet Light 60.5cm
From £30.99
24V LED Driver 40W
From £26.95
See all T5 LED Under Cabinet · See all Strip Lights · See all LED Strip Drivers 12V & 24V · LED Strip Lights: The Complete Guide to Tape, Drivers and Profiles · Motion Sensor Strip Lights for Wardrobes, Stairs and Cupboards: Mains or Battery? · Warm White vs Cool White: 3000K or 4000K for Every Room
Common questions
What is the best under cabinet lighting for a kitchen?
LED strip in an aluminium profile with a diffuser gives the most even, continuous light. For a quick upgrade without new wiring, linkable plug-in T5 fittings or a plug-in LED kit work well.
Where should under cabinet lights be placed?
Towards the front of the cabinet underside, behind the pelmet. That lights the whole depth of the worktop and hides the light source from your eyes.
How do you wire under cabinet lighting?
Plug-in kits go into a socket. For a permanent installation, an electrician feeds the driver or fittings from a switched fused spur or the lighting circuit.
Are battery under cabinet lights any good?
For cupboards and larders, yes. They are made for short bursts of light with a motion sensor, so they are not a substitute for mains worktop lighting while you cook.
Should under cabinet lights be warm or cool white?
Match the ceiling lights. If you want crisper task light, go one step cooler, for example 4000K under 3000K downlights.
Where do you put the LED driver for under cabinet lights?
Somewhere ventilated and accessible, such as on top of the wall cabinets behind the cornice. Never seal it behind a panel, bury it in insulation or put it above the hob.
What lights are used for kitchen plinths?
Sealed LED strip, IP65 or better, in a profile under the cabinet base shining down, with the driver kept up in a cabinet.
Planning a lighting project?
Need a part matched, a datasheet or a price for a large order? Call us or send a message.