600x600 LED Panels: Sizes, Grid Ceilings, Backlit vs Edge-Lit, Emergency and Fire Rated
14 min read
The short answer
A 600x600 LED panel is about 595 x 595mm and drops into a standard UK T-bar grid in place of one ceiling tile; 1200x600 and 1200x300 panels fit the same grid. In plasterboard, use a surface frame or a suspension kit. Backlit panels are deeper but have no light guide plate to age. For offices, choose UGR<19, plan for about 500 lux at the desk, and pick emergency or TP(a) diffuser versions where the job needs them.
Key takeaways
- 600x600 is the grid size. The panel itself is 595 x 595mm, so measure the T-bar centres: 600mm is the UK grid, 625mm is a continental grid a 595 panel will not fill.
- Grid ceilings take the panel in place of a tile. Plasterboard or concrete needs a surface mount frame or a suspension wire kit.
- Backlit panels point the LEDs straight down and avoid the light guide plate of edge-lit panels; edge-lit panels are slimmer.
- Offices and classrooms: ask for UGR<19 and plan around 500 lux at desks, roughly one panel per 3.5 to 4 square metres.
- A TP(a) rated diffuser is not the same as keeping a fire-resisting ceiling intact. Check the building's fire strategy before cutting into a ceiling.
On this page
- What size is a 600x600 LED panel?
- Grid ceiling or plasterboard: how do you mount a panel?
- Backlit vs edge-lit LED panels: what is the difference?
- UGR<19: why offices ask for it
- How many 600x600 LED panels do you need?
- Which colour temperature, and what is a tri-colour panel?
- Emergency 600x600 LED panels
- Fire rated 600x600 LED panels: what "fire rated" really means
- Drivers, dimming and flicker
- How long do LED panels last?
- Replacing CAT2 and other fluorescent modular fittings
- If you want the short version
- Common questions
What size is a 600x600 LED panel?
A 600x600 LED panel is the flat, square light that drops into a suspended grid ceiling in place of one ceiling tile. The name gives the grid size, not the panel size. The T-bars of a standard UK grid sit on 600mm centres, so the panel itself measures about 595 x 595mm and rests on the edges of the bars, just like the tile it replaces. That is why you see "600x600" and "595x595" used for the same product.
The same grid takes three other common sizes. Use the table to match the panel to the hole in your ceiling.
| Name you will see | Actual panel size | Fits | Ledison panels in this size |
|---|---|---|---|
| 600x600 | 595 x 595mm | One full grid tile | Pyres 30W backlit, 40W 4,400 lm UGR<19, 40W 4,800 lm tri-colour, 40W smart panel |
| 595x595 | 595 x 595mm | Same as 600x600: this is the real size | As above |
| 1200x600 | 1195 x 595mm | Two tiles side by side, or a 1200 x 600 grid | Pyres 50W backlit, 60W up to 6,600 lm UGR<19, 60W tri-colour slim |
| 1200x300 | 1195 x 295mm | A 1200 x 600 cell split by a cross tee, corridors, linear layouts | Pyres 30W backlit, 40W up to 4,600 lm |
| 625x625 | About 620 x 620mm | Continental grids, found in some European fit-outs | Not stocked: a 595 panel will not fill this grid |
If you are not sure which you have, lift a tile and measure it, then measure the distance from the centre of one T-bar to the centre of the next. Around 600mm is the UK standard. Around 625mm is the continental grid, and a 595 panel will drop straight through it.
Grid ceiling or plasterboard: how do you mount a panel?
In a grid ceiling, the panel simply replaces a tile. In a plasterboard or solid ceiling, you need a frame or a suspension kit, because there is no grid to sit on.
Recessed in a T-bar grid
Lift out a tile, feed the supply to the panel's driver, tilt the panel through the opening and lower it onto the flanges. Most 600x600 panels suit both 15mm and 24mm exposed T-bar grids. Concealed grids and tegular (stepped edge) tiles are different and may need a panel made for them. Check that the grid can take the weight: our 40W 600x600 panel weighs 3.6kg, and a 1200x600 panel with its driver weighs about 8kg. Where the ceiling installer or the panel's instructions call for it, support the panel independently from the soffit with safety wires.
Surface mounted on plasterboard or concrete
A surface mount frame is a shallow aluminium box that screws to the ceiling. The panel drops into it and the driver sits inside. Our surface mount frames come in 600x600 (599 x 603 x 50mm outside, for a 595 x 595 panel), 1200x300 and 1200x600, white, with screws and wall plugs in the box. Fix the frame into joists or with fixings rated for the weight, not into plasterboard alone.
Suspended on wires
For high ceilings, open soffits or a modern look, hang the panel on a wire kit. Ours adjusts up to 1.2m per cord, suits 600x600, 1200x300 and 1200x600 panels, and fixes to concrete, wood or plasterboard ceilings. Several of our panels can be ordered with the frame or the suspension kit chosen as the mounting option.
A flush square fit in plasterboard needs a recess frame from the panel's maker; we do not list one. If you want flush round lights instead, our round LED panels fit a cut-out from 107mm to 285mm.
Backlit vs edge-lit LED panels: what is the difference?
The difference is where the LEDs sit.
- Edge-lit: a strip of LEDs runs around the inside of the frame and shines sideways into a clear acrylic sheet called a light guide plate. Dots etched into the sheet turn the light downwards through the diffuser. That is how edge-lit panels get down to around 10mm thick.
- Backlit (also called direct-lit): the LEDs sit on the back plate, facing down, with lenses or a gap to spread the light before it reaches the diffuser. There is no light guide plate. The panel is deeper, typically around 30mm.
| Edge-lit | Backlit | |
|---|---|---|
| Depth | Slim, around 8 to 13mm | Deeper, around 30mm (our Pyres panels are 32mm) |
| Light path | Through a light guide plate | Straight down through lenses and diffuser |
| Long-term change | A cheap light guide plate can yellow with heat and age | No light guide plate to yellow |
| Best for | Shallow voids, surface frames, a minimal look | Offices and schools that want even light for many years |
| Ledison examples | 40W tri-colour 600x600 (edge-lit, 4,800 lm, 120 lm/W); 40W smart panel (8.5mm, acrylic light guide) | Pyres 600x600 30W, 1200x300 30W and 1200x600 50W, all 120 lm/W, 180 degree lenses |
Neither type is wrong, and a good edge-lit panel with a decent driver lasts well. On long-running commercial jobs, backlit panels remove one of the parts that ages.
UGR<19: why offices ask for it
UGR, the Unified Glare Rating, is a number for how much discomfort glare a lighting layout causes. Lower is better. UGR 19 is the usual limit recommended for offices, classrooms and any room where people read, write or work at screens, under the European workplace lighting standard BS EN 12464-1. Corridors and stores can accept a higher figure.
A low UGR panel uses a prismatic or micro-lens diffuser that controls the light at shallow angles, so you do not see a bright square in the corner of your eye from across the room. Strictly, UGR belongs to a whole room layout, not to one fitting, but manufacturers quote it for a standard room so you can compare panels. Our Pyres backlit panels, the 40W 4,400 lm 600x600, both 1200x600 panels and the smart panel are all stated as UGR<19.
How many 600x600 LED panels do you need?
Start with the light level the room needs, then work out the lumens. The figures below are the typical maintained illuminance recommendations in BS EN 12464-1 for common rooms.
| Area | Typical target | Notes |
|---|---|---|
| Open plan office, desks, screen work | 500 lux | UGR 19 or lower |
| Meeting and conference rooms | 500 lux | Dimming helps for presentations |
| Classrooms | 300 to 500 lux | Higher for adult evening classes |
| Reception desk | 300 lux | |
| Toilets and washrooms | 200 lux | Check the IP rating |
| Stairs | 150 lux | |
| Corridors | 100 lux | Sensors save energy here |
A worked example
An office 6m x 5m is 30 square metres. At 500 lux it needs 500 x 30 = 15,000 lumens on the desks. Not every lumen from a panel reaches the desk, and output drops over the years, so divide by a utilisation factor (say 0.6 for a typical room) and a maintenance factor (say 0.8): 15,000 / 0.48 is about 31,000 lumens from the fittings.
- With our 40W panel at 4,400 lm: 31,000 / 4,400 is about 7, so fit 8 panels in a 4 x 2 layout.
- With a Pyres 30W backlit panel at a stated 120 lm/W (about 3,600 lm): 31,000 / 3,600 is about 9, so fit 9 in a 3 x 3 layout.
As a quick check, a standard office ceiling at around 2.7m usually ends up with one 600x600 panel for every 3.5 to 4 square metres. For a full job or a compliance report, run a lighting calculation with the panel's photometric file, or send us the room sizes.
Get this right
Match the grid size (600, 625 or 1200), the ceiling type (grid, plasterboard or open soffit), the glare rating (UGR<19 for offices) and the control (Triac, 1-10V or DALI) before you order. Those four decide which panel and which accessories you need.
Which colour temperature, and what is a tri-colour panel?
Most offices and schools use 4000K, a neutral white that looks clean without feeling clinical. 3000K suits hospitality, waiting areas and homes. 5500K to 5700K is a cool white used in workshops, clinics and some retail. See our guide to warm white vs cool white for more on each.
A tri-colour or CCT panel lets you pick the colour on site, usually with a small switch on the driver. That means one product on the van covers every room on the job. Our tri-colour options:
- LED Panel 600x600 40W: 3000K, 4000K and 5500K by switch.
- Pyres 600x600 30W and 1200x300 30W backlit: switchable colour temperature, 3000K, 4000K and 5700K on the 600x600, 3000K, 4000K and 5500K on the 1200x300. The Pyres 1200x600 50W is listed as tri-colour too.
- 1200x600 tri-colour slim panel: switchable 3000K, 4000K or 5700K.
- Smart LED Panel 600x600 40W: tunable from 2700K to 6500K from the app.
Set every panel in a room to the same colour before you close the ceiling.
Emergency 600x600 LED panels
An emergency panel is a normal panel with a battery pack and a test switch, so the same fitting provides escape lighting if the mains fails. In battery mode it gives only part of its normal output, so base the emergency design on the emergency output.
- The Pyres backlit panels can be ordered with a lithium emergency pack or as a DALI emergency version, both with a 3 hour duration, in any of the dimming options.
- To convert a panel yourself, the Liteplan NLP/1 TP40 is a remote mounted LED emergency conversion kit: 3 hours, maintained or non-maintained, a 3.2V 3.8Ah LiFePO4 battery, 24 hour recharge, and an LED voltage range of 6V to 55V. Check that the panel's LED voltage sits inside that window before you buy, and ask us if you are unsure.
Emergency lighting has its own design, testing and record keeping rules. Our guide to maintained vs non-maintained emergency lighting covers them.
Fire rated 600x600 LED panels: what "fire rated" really means
Fire rated 600x600 LED panel can mean two different things.
A TP(a) rated diffuser
This is about the diffuser, the plastic face of the panel. Building Regulations guidance in England classes some thermoplastic materials as TP(a), meaning a rigid material that does not keep burning. Ceilings in many spaces have limits on how much plastic lighting diffuser can be used, and TP(a) diffusers are treated more favourably. Our Pyres panels use a TP(a) rated polycarbonate diffuser that self-extinguishes within 5 seconds of the flame being removed. The LED Panel 600x600 40W has a fire-rated TP(a) diffuser and lists the IEC 60695-2-11 850°C glow wire test, and the 1200x600 60W panel has a TP(a) rated diffuser too.
Keeping a fire-resisting ceiling intact
This is a different question. Some suspended ceilings form part of the fire protection of the floor above, or of an escape route. Cutting a fitting into that ceiling can weaken it, just as a downlight can weaken a plasterboard ceiling. A TP(a) diffuser does not, by itself, restore the ceiling's fire resistance. Where the ceiling is a fire-resisting membrane, you need a fitting or a fire hood that has been tested with that ceiling system, and the ceiling maker's guidance. Check the building's fire strategy rather than assume the ceiling is decorative. Our fire rated downlights guide explains the principle for plasterboard ceilings.
Drivers, dimming and flicker
Inside or on top of every panel is a constant current LED driver. It decides how steady the light is, whether the panel dims, and very often how long the panel lasts.
- Flicker. A poor driver passes mains ripple through to the LEDs, and you see it as shimmer on screens or in your peripheral vision. Look for a driver with a published flicker figure. Our Boke BK-CWL030 30W replacement driver states a flicker percentage of 0.136% at 100Hz. If panels on a job do flicker, our LED flickering guide walks through the causes.
- Dimming. Many of our 600x600 panels, including the Pyres range and the 40W panels, come as non-dimmable, AC Triac, 1-10V or DALI versions. Triac works with an LED rated wall dimmer. 1-10V and DALI need control wiring and a matching controller, and DALI suits offices with sensors and scenes. Our DALI, 0-10V and 1-10V guide explains the choice.
- Replacing a failed driver. When a panel goes dark, suspect the driver first. Match the current (mA) and voltage window on the old label. Our Boke drivers include the 31.5W PQL (30V to 42V, 750mA, flicker-free, independent Class II with loop in and loop out terminals), the 22W PQL (28V to 42V, 450mA to 600mA) and the 30W CWL linear (28V to 42V, 750mA fixed). Our LED drivers guide covers how to match one.
How long do LED panels last?
Our 40W 600x600 panels, the 1200x300 40W and the 1200x600 60W and tri-colour slim panels are rated at 50,000 hours, and both 1200x600 panels state 80% of their light still there after 50,000 hours. At 10 hours a day, 5 days a week, 50 weeks a year, that is 2,500 hours a year, or about 20 years. Our smart panel is rated at 40,000 hours. Our Boke drivers state a nominal life of up to 100,000 hours.
Installers on forums such as r/led ask why panels that look the same on paper behave so differently after a year or two. The answer is usually four things: the driver, heat, the quality of the LEDs, and, in edge-lit panels, the light guide plate. So choose a named driver with stated flicker and lifetime figures, keep it out of insulation, prefer backlit where long-term light quality matters, and buy panels with a separate driver so a failure is a quick swap, not a new panel.
Replacing CAT2 and other fluorescent modular fittings
Many UK offices still have 600x600 fluorescent modular fittings: four 18W T8 tubes behind a silver CAT2 louvre, designed in the 1990s for rooms with computer screens, or 2D and compact fluorescent recessed modules. Fluorescent tubes are being phased out of sale in the UK, so these fittings are getting harder to keep running. Our guide to replacing fluorescent tubes with LED covers the tube options, but for a grid ceiling the cleaner job is usually to swap the whole fitting for a panel.
- Isolate the circuit at the distribution board and prove it dead.
- Lift the louvre fitting out of the grid, with someone holding it, and disconnect it.
- Connect the panel's driver to the supply, following its terminal markings. For an emergency version, connect the permanent live as well.
- Set the colour switch, lower the panel onto all four flanges, then test. Test and record emergency panels too.
A four tube 18W modular fitting draws well over 70W once the control gear is counted. A 30W to 40W panel usually gives as much useful light on the desk or more, with no tubes to change. Replace like for like in the same grid positions, and keep emergency fittings in the same places unless the emergency lighting design is redone.
Safety: when to call an electrician
Fitting a panel means connecting it to the mains, and on commercial jobs often to emergency and control circuits too. Have a qualified electrician do the work, test the circuit and certify it. In homes in England and Wales, electrical work falls under Part P of the Building Regulations. Ask for advice before cutting fittings into any ceiling that may be fire-resisting.
For installers
- Pyres backlit: 120 lm/W, UGR<19, TP(a) PC diffuser, IP44, 32mm; non-dimmable, Triac, 1-10V or DALI; lithium or DALI emergency, 3 hours.
- LED Panel 600x600 40W: 4,400 lm, 110 lm/W, CRI>80, UGR<19, IP40, 595 x 595 x 10mm, 3.6kg, 5 year warranty.
- Surface frame PL0606: part no. 27-PL060601, for 595 x 595 panels, 599 x 603 x 50mm, aluminium, white, 1.0kg.
- Liteplan NLP/1 TP40: 6V to 55V LED range, 2 to 20 LEDs in series, 320mA LED current limit, 3 hour LiFePO4 pack, maintained or non-maintained.
- Boke BK-CWL030-B0750A: 750mA fixed, 28V to 42V, PF 0.98, supports central and self-contained emergency systems.
If you want the short version
A 600x600 LED panel is really 595 x 595mm and drops into a UK grid; 1200x600 and 1200x300 fit the same grid. In plasterboard, use a surface frame or wires. Backlit for long, even service, edge-lit where depth is tight. UGR<19 and about 500 lux for offices. A TP(a) diffuser is not a fire-resisting ceiling, and the driver decides how long the panel lasts.
Products that help
600x600 LED Panel 30W
From £31.99
LED Panel 600x600 40W
From £33.99
1200x600 LED Panel 50W
From £55.95
Surface Mount Frame for 600x600 LED Panel
From £25.95
See all LED Panel Lights · See all LED Back-Lit Panels · See all Constant Current LED Drivers · Emergency Lighting Explained: Maintained vs Non-Maintained, Testing and the Rules · How to Replace a Fluorescent Tube with LED: the Ban, Starters and Ballast Bypass · Fire Rated Downlights: Do You Need Them? UK Rules in Plain English
Common questions
Is a 600x600 LED panel actually 600mm?
No. It is about 595 x 595mm so it can rest on the flanges of a grid whose T-bars sit on 600mm centres. 600x600 and 595x595 describe the same panel.
Can you fit a 600x600 LED panel in a plasterboard ceiling?
Yes, with a surface mount frame screwed to the ceiling or a suspension wire kit. A flush fit needs a plasterboard recess frame from the panel's maker. Fix into joists or with fixings rated for the weight.
Which is better, a backlit or an edge-lit LED panel?
Backlit panels are deeper but have no light guide plate to yellow, so they tend to hold their light quality longer. Edge-lit panels are slimmer and suit shallow voids and surface frames. A good driver matters more than either design.
What does UGR<19 mean on an LED panel?
UGR is the Unified Glare Rating. 19 or lower is the usual limit recommended for offices, classrooms and screen work, so panels quoted as UGR<19 suit those rooms.
How many LED panels do I need for an office?
Plan for about 500 lux at the desks. With 4,000 lm class panels and a typical 2.7m ceiling, that usually works out at one 600x600 panel for every 3.5 to 4 square metres. For a full job, run a lighting calculation with the panel's photometric file.
Are fire rated 600x600 LED panels needed in a suspended ceiling?
It depends on the ceiling. A TP(a) diffuser covers the plastic face of the panel. If the suspended ceiling is a fire-resisting membrane, you need a fitting or fire hood tested with that ceiling system, so check the fire strategy first.
How long do 600x600 LED panels last?
Our 40W 600x600 panels are rated at 50,000 hours, about 20 years at 2,500 hours a year. In practice the driver and heat decide the real life, so choose a named driver and keep it out of insulation.
Planning a lighting project?
Need a part matched, a datasheet or a price for a large order? Call us or send a message.